Notes for Use of Fujitsu Flash MCU Programmer for FR

December 2008
Fujitsu Limited

This software writes data to flash memory contained in the Fujitsu microcontroller with flash memory
from a personal computer.

1.  System Requirements
	Personal computer:  IBM PC/AT compatibles with RS-232C port
	OS:  Japanese and English versions of Windows 2000 SP3, Windows XP SP2
	Memory:  Memory capacity more than OS requires
	Available disk space:  10 MB or more

	NOTICE:  The operations of all models that meet the above conditions may not be ensured.

2.  Explanation of Files Provided
	PCWFRsetup.exe:  Installer execution file
	ReadmeFRe.txt:  Document file(english)
	ReadmeFRj.txt:  Document file(japanese)

3.  Installation Procedure
3.1  Outline of Installer
	This installer includes the program for storage of installation information, called Windows 
	Installer.  Windows Installer is installed to the personal computer on which Windows 2000 or 
	earlier OS runs.  In this case, restart may be required.
	If the installation of Windows Installer is completed or Windows Installer has been preinstalled, 
	the installation of this software is started.  Before installation, be sure to uninstall the old
	version and reboot.

3.2  Setup Mode
	When Installer is started in the Setup mode, the window for the selection of "All" or "Custom"
	appears:
	"All" is the standard setup and should be selected.
	"Custom" should be selected only when setting the installation folder in a special place.
	Installation to a deep hierarchy of the folder may prevent Installer from operating.  The full
	path of the folder should be specified within 200 characters and the full path of the 8.3-format
	folder within 100 characters.
	When the operation is continued according to directions from Installer, the installation is 
	completed and the shortcut to this software is created as a program on the Start menu.

4. Uninstallation Procedure
	Open the "Start"-"Settings" "Control Panel" and start "Add/Remove Programs."  Select and 
	delete "FUJITSU FLASH MCU Programmer for FR."  After uninstallation, the 
	installation folder may be left.  In this case, delete the folder manually.  This software is 
	typically installed to Fujitsu\Fujitsu Flash MCU Programmer\FR below Program Files.  No 
	registry is used.

5. Cautions
	No operation of this software on the NEC PC98 series of personal computers is assured.
	This software is not intended for writing to mass-produced products.

Note:  Windows is the product name of Microsoft.



-------------------------------------------------------------------------------
History of update
V01L20
	add MB91F469G
	add MB91F777

V01L19
	add MB91F224
	MB91F460 Suffix change
	correct 610
	Caution change

V01L18
	add 467BA/CA/DA
	add 610
	add 644

	OS:Windows 2000 SP3, Windows XP SP2
	COM PORT 1-20

V01L17
	Internal motorola S decoder specifiction is added.
	When operation ends, Com Port is opened. 
	add 467MA,273,482,662,637

V01L16
	The HELP file is corrected. 

V01L15
	operation on WindowsNT is no longer guaranteed.
	add 313,467BA,487,639,647

V01L14
	356->356B (Speed Up)
	467RA     (Speed Up, HWWDT Clear, SMRFSCKE=0)
	add 463NA,249/S

V01L13
	add 213,479,464AA,465KA,467RA,475,478,211

V01L12
	add 223,346,319R PROG,319R FONT

V01L11
	add 248,318R,345,314

V01L10a
	add 267,272,356
	add 319A
	change 4,8MHz-OSC for 264.
	delete 154
	delete 005
	delete 005A
	delete 120

V01L09
	add	310,312
	CRC checking is added
	internal Motorola S decoder is added
	continuously writeing mode is deleted
	A temporary(binary) file is not created
	popup menu is changed

V01L08
	add 365/366/367/368
	add 264(provisional)

V01L07
	add 369

V01L06
	operation on windows95 is no longer guaranteed.
	add 353,355.

V01L05
	add 233.
	change security address and security data length for 154/155.
	make temporary file in everytime
	change DOWNLOAD sequence .

V01L04
	add 158,362.


